Method of operation machine for sealing vacuum

Vacuum packaging machine relative to other vacuum sealing machine operation, although slightly different, but similar.

首先,接通电源:开启电源开关，电源指示灯亮。

First, connect the power supply: turn on the power switch, the power indicator light.

然后,设定抽气时间：调整抽气时间范围为0－99秒之间，抽气时间越长，则获得真空度越高。根据包装物品的需要，选择最佳的抽气时间，以获得合适的真空度。开机后数码管显示,即表示待机状态。按一次抽气键，显示原设定值，且10秒位闪烁，此时可用增加键或减少键,设定所需时间的10秒位值，再按一次设定秒位，最后调整下需要的数据。再按一次返回待机状态。

Then, set the pumping time: adjust the pumping time range between 0 and 99 seconds, the pumping time is longer, then obtain the higher the vacuum. According to the needs of packaging items, choose the best time of pumping, vacuum degree appropriate to obtain. The digital tube display after boot, the standby state. According to a pumping button, display the original setting value, and 10 seconds flashing, there can increase or reduce the key button 10 seconds, set a value in the time required, then press set seconds at a time, required data finally adjust. Press again to return to the standby state.

紧接着,热封温度和热封时间的调定：第一步,根据包装袋的薄厚材料及被包装物品的不同，选择面板上最佳的热封温度以及热封时间，以获得最佳的封口强度，调试时一般由低温往高温调整，设定到封口所需外观及强度为止。第二步,在待机状态下，按温度键,可设定所需要的低中高温度值。第三步,热封时间设定时，在待机状态下，首先按一次热封键，显示原设定值，且秒位闪烁，可用增加键或减少键，设定所需要时间的秒位值，再按一次设定1秒位，最后再按一次键，返回到待机状态。

Then, heat sealing temperature and heat sealing time setting: the first step, according to the package materials and different thickness of the packaged goods on the selection panel, the best heat sealing temperature and heat sealing time, in order to obtain the best sealing strength, from low to high temperature when debugging in general adjustment, set to seal the required appearance and strength. The second step, in the standby mode, press the button can be low temperature, high temperature setting the desired value. The third step, heat sealing time setting, in the standby mode, the first by a heat sealing button, display the original setting value, and the second bit flash, can increase or reduce the key button, set the seconds value takes time, press again set a second position, then press a key, return to the standby state.

随后,各参数设定好后，将所需包装物品装入包装袋（塑料复合袋或铝箔复合袋），放入真空室，提起压条，均匀地把袋口置于下热封架上排好，然后放下压条。

Then, the parameters are set, the required packaging bag (bags of plastic or aluminum foil compound bag), into the vacuum chamber, filed a layering, evenly placed under the mouth heat sealing frame lined up, and then down.

然后,压下有机玻璃真空盖，面板上抽气指示灯亮。真空泵开始抽气，机盖即被自动吸引闭合，程序自动运行，整个工作流程是：1\抽气：数码管从０开始计数到设定时间数值后，抽气指示灯随之熄灭，热封指示灯亮，此时电磁阀动作，转到b热封程序，数码管从０.0开始计数时间的设定值,时间到后,转为c保温二秒时段，数码管显示热封时间的设定值，，转到放秒程序，此时放气电磁阀动作，大气进入真空室，真空盖自动抬起，至此真空包装结束，转到待机状态，准备进行下次包装循环。

Then, press the organic glass vacuum cover, pumping panel lights. Vacuum pump to start pumping, machine cover is closed automatically attract, the program automatically, the work flow is: 1\ pumping: digital tube counting begins at 0 to set the time value, the pumping light is extinguished, heat sealing indicator light, when the electromagnetic valve action, go to the B heat sealing process, digital tube start counting time value from 0, after time, converted to C insulation two seconds time, digital tube display heat sealing time settings, to put this program, second, gas solenoid valve action, the air into the vacuum chamber, the vacuum cover lift automatically, thus vacuum packaging end, to the standby state, ready for the next packaging recycling.

最后按下急停按键,在工作时，若出现异常情况或想提前结束工作流程，只须按一下急停键,就可以恢复正常或停止包装工作，随即返回到待机状态,这样整个操作步骤就完成了。　　　

Finally, press the emergency stop button, at work, if any abnormal situation or to terminate the work flow, simply press the emergency stop button, can return to normal or stop the packing work, then return to the standby state, so that the entire operation is complete.